Experiment : Build Your Own Hovercraft

2 min


0
591 shares
Experiment : Build Your Own Hovercraft
Advertisements

Owning a Hovercraft is Extremely a lot of fun, Here are all instructions you need to build your own Hovercraft that you can ride on.

How does your hovercraft work?

Air can have tremendous lift. In fact, moving air is what allows large planes to get off the ground. When you power on the blower, it forces air out the holes of the tarp and towards the edge of the hovercraft.

While you might think it would be difficult for a small blower to lift over 100 pounds, it is not. Since the large volume of moving air is spread out over a relatively thin area, it has a surprising amount of lift. The layer of air greatly reduces friction allowing you to glide on a cushion of air.

 

Building A Hovercraft

If you just follow these instructions you will build your own Hovercraft in a few hours.

You will Need the following
  • Piece of heavy-duty tarp material 5’ X 5’
  • .25 inch machine bolt (1.5 inches long) with nut
  • Plastic cover for a round electrical box
  • 4’ X 4’ 3/4 inch plywood
  • Leaf blower (cordless electric leaf blowers are great – we used a Makita BUB182Z)
  • Lawn chair (optional)
  • String
  • Pencil
  • 2 2-inch washers for the bolt
  • TOOLS: (adult use only) jig saw, staple gun, drill, utility knife, sandpaper

Building Progress

Mark the center of the plywood by drawing lines between opposite corners.Nail a small nail into the center of the panel and use a pencil tied to a piece of string as a compass to draw a 4’ circle as shown

Using a jig saw, carefully cut the circle out of the panel and sand the edges smooth and round with sandpaper.

Measure the width of the leaf blower output and use a hole cutter or jig saw to cut a hole the same width. It should be about 2 feet from the center of the plywood and it should fit snug. (use duct tape around the blower if needed to tighten up the seal.)

If you want to attach a seat (or anything else) to the top, now would be the time. Drill holes and attach with machine screws. Install the machine screws through the bottom, and counter-sink all screws to keep the bottom of the craft smooth.

Advertisements

Lay the plywood on the center of the tarp and wrap the tarp over the edge. Staple the tarp onto the top of the hovercraft with a staple gun along the edge so that the staples almost touch each other. Be sure to keep the tarp as taught as possible while stapling. When finished, you can trim any extra tarp material away with scissors if desired.

Drill a 1/4 inch hole through the center of the plywood/tarp and also through the center of the electrical box cover.

Feed the bolt through a washer and the plastic cover, and then up through the hovercraft. Secure with a washer and the nut from the top as shown. Cover the screw head with duct tape to avoid scratching the floor.

Use a utility knife or hobby knife to carefully cut 6 evenly spaced holes into the tarp material in a circle about 10 inches from the center. The holes should be about 1.5 inches wide. (You can use an American quarter to trace the circles.)

To make bumpers, you can cut foam pipe insulation and attach to the outside edge with hot glue. For extra style when using at night or indoors, add 12 volt LED strip lights and power with a 9 volt battery.Construction is complete, you are ready to hover!

Riding on your Hovercraft

Center yourself on the top of the hovercraft sitting on chair, Power up the blower and have someone give you a push. You’re off and hovering on air.

Your hovercraft works best on smooth surfaces such as hard floors, concrete, or smooth asphalt. Using the hovercraft on bumpy surface can affect performance or, even worse, it could end up ripping the tarp.

Please careful, Hovercrafts do not have brakes or steering! Use away from objects, people, pets, or traffic that you might run into. unless you invent a brakes and\or steering for it.

Be sure to wear a helmet and have someone standing by to help guide your hovercraft. Leaf blowers can also be loud, so ear protection is recommended.

Propulsion

Giving your hovercraft propulsion is necessary, but it allows the rider to move the craft on its own, and sort of provides some directional control.

On the video, we used CO2 fire extinguishers specially modified by a special effects company. Modifying a fire extinguisher is quite dangerous and should not be attempted.

However, an unmodified CO2 extinguisher will often work (although CO2 extinguishers can be an expensive.) An easier way to get thrust is to simply use an additional leaf blower for propulsion. Be sure to point it in the opposite direction that you want to go.

Advertisements

Like it? Share with your friends!

0
591 shares

What's Your Reaction?

hate hate
2128
hate
confused confused
912
confused
fail fail
3040
fail
fun fun
2736
fun
geeky geeky
2432
geeky
love love
1520
love
lol lol
1824
lol
omg omg
912
omg
win win
3040
win

0 Comments

Leave a Reply

Choose A Format
Personality quiz
Series of questions that intends to reveal something about the personality
Trivia quiz
Series of questions with right and wrong answers that intends to check knowledge
Poll
Voting to make decisions or determine opinions
Story
Formatted Text with Embeds and Visuals
List
The Classic Internet Listicles
Open List
Submit your own item and vote up for the best submission
Ranked List
Upvote or downvote to decide the best list item
Meme
Upload your own images to make custom memes
Video
Youtube, Vimeo or Vine Embeds
Audio
Soundcloud or Mixcloud Embeds
Image
Photo or GIF
Gif
GIF format